View T315HW07-V1_7741069.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 1 / 30
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 2 / 30 contents no contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specification 3-1 electriacl characteristics 3-2 interface connections 3-3 signal timing specification 3-4 signal timing waveform 3-5 color input data reference 3-6 power sequence 3-7 backlight specification 4 optical specification 5 mechanical characteristics 6 reliability test items 7 international standard 7-1 safety 7-2 emc 8 packing 8-1 definition of label 8-2 packing methods 8-3 pallet and shipment information 9 precaution 9-1 mounting precautions 9-2 operating precautions 9-3 electrostatic discharge control 9-4 precautions for strong light exposure 9-5 storage 9-6 handling precautions for protect film
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 3 / 30 record of revision version date page description 0.0 2010/05/05 first release 0.1 2010/05/31 final spec 0.2 2010/06/21 20,21 update front/back view drawings 16 update response time (g to g) to 5.5 ms
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 4 / 30 1. general description this specification applies to the 31.5 inch color t ft-lcd module t315hw07 v1. this lcd module has a tf t active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 31.5 inch. this modul e supports 1,920x1080 mode. each pixel is divided into red, gr een and blue sub-pixels or dots which are arranged in vertical stripes. gray scale or the brightness of the sub-pi xel color is determined with a 10-bit gray scale si gnal for each dot. the t315hw07 v1 has been designed to apply the 10-b it 2 channel lvds interface method. it is intended to support displays where high brightness, wide viewin g angle, high color saturation, and high color dept h are very important. * general information items specification unit note active screen size 31.55 inch display area 698.40(h) x 392.85(v) mm outline dimension 739.6(h) x 440.0 (v) x 24.1(d) mm d : front bezel to t-con cover driver element a-si tft active matrix display colors 10 bit(8+frc), 1073.7m colors number of pixels 1,920x1080 pixel pixel pitch 0.3638 (h) x 0. 3638 (w) mm pixel arrangement rgb vertical stripe display operation mode normally black surface treatment anti-glare, 3h haze=11%
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 5 / 30 2. absolute maximum ratings the followings are maximum values which, if exceede d, may cause faulty operation or damage to the unit item symbol min max unit conditions logic/lcd drive voltage vcc -0.3 14 [volt] note 1 input voltage of signal vin -0.3 4 [volt] note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 10 90 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 10 90 [%rh] note 2 panel surface temperature pst 65 [ o c] note 3 note 1: duration:50 msec. note 2 : maximum wet-bulb should be 39 and no conde nsation. the relative humidity must not exceed 90% non-conde nsing at temperatures of 40 or less. at temperature s greater than 40 , the wet bulb temperature must not exceed 39 . note 3: surface temperature is measured at 50 dry condition
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 6 / 30 3. electrical specification the t315hw07 v1 requires two power inputs. one is e mployed to power the lcd electronics and to drive t he tft array and liquid crystal. the second is employed fo r led lightbar. 3.1 electrical characteristics value parameter symbol min. typ. max unit note lcd power supply input voltage v dd 10.8 12 13.2 v dc 1 power supply input current i dd - 1.1 1.42 a 2 power consumption p c 13.2 17.0 watt 2 inrush current i rush 3 a 3 differential input high threshold voltage v th -- -- +100 mv dc 4 differential input low threshold voltage v tl -100 -- -- mv dc 4 lvds interface input common mode voltage v icm 1.1 1.25 1.4 v dc 4 lvds interface input channel pair skew margin t skew (cp) -500 -- +500 ps 5 input high threshold voltage v ih (high) 2.7 -- 3.3 v dc cmos interface input low threshold voltage v il (low) 0 -- 0.6 v dc life time (mttf) 30000 -- hours 6,7 note : 1. the ripple voltage should be controlled under 10% o f v cc 2. test condition: (1) v dd = 12.0v (2) fv = type timing, 60hz, 120hz or other (3) f clk = max freq. (4) temperature = 25 (5) test pattern : white pattern
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 7 / 30 3. measurement condition : rising time = 400us gnd gnd gnd gnd v vv v dd dddd dd 10% 90% 400 400400 400 s 4. v icm = 1.25v v vv v th thth th v vv v icm icm icm icm v vv v tl tltl tl 0 00 0v vv v 5. input channel pair skew margin 6. the relative humidity must not exceed 80% non-conde nsing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperat ure must not exceed 39 . when operate at l ow temperatures, the brightness of led will drop and t he life time of led will be reduced. 7. the lifetime (mttf) is defined as the time which lu minance of led is 50% compared to its original valu e. [operating condition: continuous operating at ta = 252 ]
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 8 / 30 3.2 interface connections lcd connector: fi-re51s-hf (jae, lvds connector) pin symbol description pin symbol description 1 v dd power supply, +12v dc regulated 26 ch2_0+ lvds channel 2, signal 0+ 2 v dd power supply, +12v dc regulated 27 ch2_1- lvds channel 2, signal 1- 3 v dd power supply, +12v dc regulated 28 ch2_1+ lvds channel 2, signal 1+ 4 v dd power supply, +12v dc regulated 29 ch2_2- lvds channel 2, signal 2- 5 v dd power supply, +12v dc regulated 30 ch2_2+ lvds channel 2, signal 2+ 6 reserved auo internal use only 31 gnd ground 7 gnd ground 32 ch2_clk- lvds channel 2, clock - 8 gnd ground 33 ch2_clk+ lvds channel 2, clock + 9 gnd ground 34 gnd ground 10 ch1_0- lvds channel 1, signal 0- 35 ch2_3- lvds channel 2, signal 3- 11 ch1_0+ lvds channel 1, signal 0+ 36 ch2_3+ lvds channel 2, signal 3+ 12 ch1_1- lvds channel 1, signal 1- 37 reserved auo internal use only 13 ch1_1+ lvds channel 1, signal 1+ 38 reserved auo internal use only 14 ch1_2- lvds channel 1, signal 2- 39 gnd ground 15 ch1_2+ lvds channel 1, signal 2+ 40 scl eeprom serial clock 16 gnd ground 41 sda eeprom serial data 17 ch1_clk- lvds channel 1, clock - 42 vsync vsync output to system board 18 ch1_clk+ lvds channel 1, clock + 43 bus_sw bus_sw (sony internal use only) 19 gnd ground 44 panel_sel panel_sel (sony internal use only) 20 ch1_3- lvds channel 1, signal 3- 45 set_on2 set_on2 (sony internal use only) 21 ch1_3+ lvds channel 1, signal 3+ 46 sa_mode sa_mode (sony internal use only) 22 reserved auo internal use only 47 panel_on panel_on (10kohm to gnd) 23 reserved auo internal use only 48 frc_rst frc_rst (sony internal use only) 24 gnd ground 49 hsync hsync output to system board 25 ch2_0- lvds channel 2, signal 0- 50 tcon_rdy send tcon ready to system 51 fr_sel 10kohm to gnd
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 9 / 30 lvds option = high/open ns b bb b 2 22 2 n a n an a n a d e d ed e d e d e d ed e d e b bb b 2 22 2 b bb b 3 33 3 b bb b 4 44 4 b bb b 5 55 5 n a n an a n a b bb b 3 33 3 r rr r 0 00 0 r rr r 5 55 5 g gg g 0 00 0 g gg g 0 00 0 r rr r 0 00 0 r rr r 1 11 1 r rr r 2 22 2 r rr r 3 33 3 r rr r 4 44 4 r rr r 1 11 1 g gg g 1 11 1 b bb b 0 00 0 b bb b 1 11 1 b bb b 1 11 1 g gg g 1 11 1 g gg g 2 22 2 g gg g 3 33 3 g gg g 4 44 4 g gg g 5 55 5 g gg g 2 22 2 c lo c k c lo c k c lo c k c lo c k c h x c h x c h x c h x _ __ _ 0 00 0 + ++ + c h x c h x c h x c h x _ __ _ 0 00 0 - -- - c h x c h x c h x c h x _ __ _ 1 11 1 + ++ + c h x c h x c h x c h x _ __ _ 1 11 1 - -- - c h x c h x c h x c h x _ __ _ 2 22 2 + ++ + c h x c h x c h x c h x _ __ _ 2 22 2 - -- - c h x c h x c h x c h x _ __ _ 3 33 3 + ++ + c h x c h x c h x c h x _ __ _ 3 33 3 - -- - c h x c h x c h x c h x _ __ _ 4 44 4 + ++ + c h x c h x c h x c h x _ __ _ 4 44 4 - -- - r rr r 6 66 6 b bb b 7 77 7 n a n an a n a n a n an a n a r rr r 6 66 6 r rr r 7 77 7 g gg g 6 66 6 g gg g 7 77 7 b bb b 6 66 6 r rr r 7 77 7 r rr r 8 88 8 b bb b 9 99 9 n a n an a n a n a n an a n a r rr r 8 88 8 r rr r 9 99 9 g gg g 8 88 8 g gg g 9 99 9 b bb b 8 88 8 r rr r 9 99 9 p re v io u s c y c le c u rre n t c y c le n e x t c y c le p re v io u s c y c le c u rre n t c y c le n e x t c y c le p re v io u s c y c le c u rre n t c y c le n e x t c y c le p re v io u s c y c le c u rre n t c y c le n e x t c y c le note: x = 1, 2, 3, 4? lvds option = low jeida b bb b 6 66 6 n a n an a n a d e d ed e d e d e d ed e d e b bb b 6 66 6 b bb b 7 77 7 b bb b 8 88 8 b bb b 9 99 9 n a n an a n a b bb b 7 77 7 r rr r 4 44 4 r rr r 9 99 9 g gg g 4 44 4 g gg g 4 44 4 r rr r 4 44 4 r rr r 5 55 5 r rr r 6 66 6 r rr r 7 77 7 r rr r 8 88 8 r rr r 5 55 5 g gg g 5 55 5 b bb b 4 44 4 b bb b 5 55 5 b bb b 5 55 5 g gg g 5 55 5 g gg g 6 66 6 g gg g 7 77 7 g gg g 8 88 8 g gg g 9 99 9 g gg g 6 66 6 c lo c k c lo c k c lo c k c lo c k r rr r 2 22 2 b bb b 3 33 3 n a n an a n a n a n an a n a r rr r 2 22 2 r rr r 3 33 3 g gg g 2 22 2 g gg g 3 33 3 b bb b 2 22 2 r rr r 3 33 3 c h x c h x c h x c h x _ __ _ 0 00 0 + ++ + c h x c h x c h x c h x _ __ _ 0 00 0 - -- - c h x c h x c h x c h x _ __ _ 1 11 1 + ++ + c h x c h x c h x c h x _ __ _ 1 11 1 - -- - c h x c h x c h x c h x _ __ _ 2 22 2 + ++ + c h x c h x c h x c h x _ __ _ 2 22 2 - -- - c h x c h x c h x c h x _ __ _ 3 33 3 + ++ + c h x c h x c h x c h x _ __ _ 3 33 3 - -- - c h x c h x c h x c h x _ __ _ 4 44 4 + ++ + c h x c h x c h x c h x _ __ _ 4 44 4 - -- - r rr r 0 00 0 b bb b 1 11 1 n a n an a n a n a n an a n a r rr r 0 00 0 r rr r 1 11 1 g gg g 0 00 0 g gg g 1 11 1 b bb b 0 00 0 r rr r 1 11 1 p re v io u s c y c le c u rre n t c y c le n e x t c y c le p re v io u s c y c le c u rre n t c y c le n e x t c y c le p re v io u s c y c le c u rre n t c y c le n e x t c y c le p re v io u s c y c le c u rre n t c y c le n e x t c y c le note: x = 1, 2, 3, 4?
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 10 / 30 3.3 signal timing specification this is the signal timing required at the input of the user connector. all of the interface signal tim ing should be satisfied with the following specifications for its proper operation. timing table signal item symbol min. typ. max unit period tv - 1134 - th active tdisp (v) 1080 th blanking tblk (v) - 54 - th front porch tfp (v) - 34 - th back porch tbp (v) - 16 - th v_sync tvsync_wdth - 4 - th vertical section polarity pol (v) + period th - 1092 - tclk active tdisp (h) 960 tclk blanking tblk (h) - 132 - tclk front porch tfp (h) - 16 - tclk back porch tbp (h) - 100 - tclk h_sync thsync_wdth - 16 - tclk horizontal section polarity pol (h) + clock frequency fclk=1/tclk - 74.23 - mhz vertical frequency frequency fv - 59.94 - hz horizontal frequency frequency fh - 67.97 - khz notes: (1) display position is specific by the rise of de signal only. horizontal display position is specified by the ris ing edge of 1 st dclk after the rise of 1 st de, is displayed on the left edge of the screen. (2)vertical display position is specified by the ri se of de after a ?low? level period equivalent to e ight times of horizontal period. the 1 st data corresponding to one horizontal line after th e rise of 1 st de is displayed at the top line of screen. (3)if a period of de ?high? is less than 1920 dclk or less than 1080 lines, the rest of the screen dis plays black. (4)the display position does not fit to the screen if a period of de ?high? and the effective data per iod do not synchronize with each other.
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 11 / 30 3.4 signal timing waveforms th tdisp(v) tblk(v) tv de rgb data line n invalid data invalid data line 1 line 2 line 3 line n line 4 tclk clk de ch1 ch2 pixel m-15 pixel m-11 pixel m-7 pixel m-3 pixel m-14 pixel m-10 pixel m-6 pixel m-2 invalid data invalid data pixel 1 pixel 2 pixel 5 pixel 9 pixel 6 pixel 10 pixel 13 pixel 14 pixel 17 pixel 18 pixel 21 pixel 22 pixel m-11 pixel m-7 pixel m-3 pixel m-10 pixel m-6 pixel m-2 invalid data invalid data pixel 1 pixel 2 pixel 5 pixel 6 th tdisp(h) tblk(h) ch3 ch4 pixel m-13 pixel m-9 pixel m-5 pixel m-1 pixel m-12 pixel m-8 pixel m-4 pixel m invalid data invalid data pixel 3 pixel 4 pixel 7 pixel 11 pixel 8 pixel 12 pixel 15 pixel 16 pixel 19 pixel 20 pixel 23 pixel 24 pixel m-9 pixel m-5 pixel m-1 pixel m-8 pixel m-4 pixel m invalid data invalid data pixel 3 pixel 4 pixel 7 pixel 8 m m m m p p p p i i i i x x x x e e e e l l l l n l in e n l in e n l in e n l in e
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 12 / 30 3.5 color input data reference the brightness of each primary color (red, green an d blue) is based on the 10 bit gray scale data inpu t for the color; the higher the binary input, the brighter the color . the table below provides a reference for color ve rsus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r9 r8 r7 r6 r5 r4 r3 r2 r1 r0 g9 g8 g7 g6 g5 g4 g3 g2 g1 g0 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(1023) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 blue(1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(1022) 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 r red(1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 ---- green(1022) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 g green(1023) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ---- blue(1022) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 b blue(1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 13 / 30 3.6 power sequence for lcd standard *1 standalone *1 parameter min. type. max. type. unit t1 0.4 --- 30 --- ms t2 10 --- --- 57 ms t2a 10 --- 100 --- ms t2b 0 *4 --- 100 *4 --- ms t2c 10 --- --- --- ms t2d 10 --- --- --- ms t2e --- --- --- 102 ms t2f --- --- 250 204 ms t3 500 --- --- --- ms t4 0 *2 --- --- --- ms t5 0 --- --- --- ms t6 --- --- --- *3 --- ms t7 500 --- --- --- ms note: (1) standard mode is used for customer?s operation. standalone mode is used for panel factory operatio n. (2) t4=0 : concern for residual pattern before blu turn off. (3) t6 : voltage of vdd must decay smoothly after p ower-off. (customer system decide this value) (4) t2b : customer decides this value
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 14 / 30 3.7 backlight specification the backlight unit contains 2pcs light bar. 3.7.1 lightbar driving condition values values values values parameter parameter parameter parameter symbole symbole symbole symbole min min min min typ typ typ typ max max max max unit unit unit unit note note note note forward current forward current forward current forward current anode anode anode anode if (anode) if (anode) if (anode) if (anode) 120 ma (one lightbar) (one lightbar) (one lightbar) (one lightbar) cathode cathode cathode cathode if (cathode) if (cathode) if (cathode) if (cathode) - 120 - ma forward voltage forward voltage forward voltage forward voltage vf vfvf vf 232 264 288 v forward voltage variation forward voltage variation forward voltage variation forward voltage variation vf vfvf vf v total power consumption ( total power consumption ( total power consumption ( total power consumption (2 22 2 lightbar) lightbar) lightbar) lightbar) pbl pbl pbl pbl 27.8 31.7 34.6 w pwm operation frequency pwm operation frequency pwm operation frequency pwm operation frequency f_pwm f_pwm f_pwm f_pwm 140 180 240 hz pwm dimming duty ratio pwm dimming duty ratio pwm dimming duty ratio pwm dimming duty ratio d_pwm d_pwm d_pwm d_pwm 10 100 % note 1&2 1 led string / lightbar anode 1 cathode1 anode 2 cathode 2 2 lightbars are connected in serial
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 15 / 30 3.7.2 input pin assignment 4 pin cn: molex 51003-0400 5 pin cn: molex 51003-0500 cn2 4pin 1 + in 2 nc 3 nc 4 nc cn3 5pin 1 - out 2 nc 3 nc 4 nc 5 nc
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 16 / 30 4. optical specification optical characteristics are determined after the un it has been ?on? and stable for approximately 45 mi nutes in a dark environment at 25c. the values specified are at an approximate distance 50cm from the lcd surfac e at a viewing angle of and equal to 0. fig.1 presents additional information concerning th e measurement equipment and method. values parameter symbol min. typ. max unit notes contrast ratio cr 3200 4000 -- 1 surface luminance (white) l wh 320 400 -- cd/m 2 2 luminance variation white(9p) -- -- 1.3 3 response time (g to g) t -- 5.5 -- ms 4 color gamut ntsc 72 % color coordinates red r x 0.640 r y 0.330 green g x 0.320 g y 0.620 blue b x 0.150 b y 0.050 white w x 0.280 w y typ.-0.03 0.290 typ.+0.03 viewing angle 5 x axis, right( =0) r -- 89 -- degree x axis, left( =180) l -- 89 -- degree y axis, up( =90) u -- 89 -- degree y axis, down ( =270) d -- 89 -- degree sr3 or equivalent
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 17 / 30 note: 1. contrast ratio (cr) is defined mathematically as : surface luminance of l on5 contrast ratio= surface luminance of l off5 2. surface luminance is luminance value at point 5 across the lcd surface 50cm from the surface with a ll pixels displaying white. from more information see fig 2. when lamp current i h = 11ma. l wh =lon5 where lon5 is the luminance with all pixels displaying white at c enter 5 location. 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 ,?,l on9 )/ minimum(l on1 , l on2 ,?l on9 ) 4. response time t is the average time required for display transition by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness mat rix) and is based on f v =120hz to optimize. target measured response time 0% 25% 50% 75% 100% 0% 0% to 25% 0% to 50% 0% to 75% 0% to 100% 25% 25% to 0% 25% to 50% 25% to 75% 25% to 100% 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100% 75% 75% to 0% 75% to 25% 75% to 50% 75% to 100% start 100% 100% to 0% 100% to 25% 100% to 50% 100% to 75% 5. viewing angle is the angle at which the contras t ratio is greater than 10. the angles are determin ed for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig3. fig. 2 luminance 1 2 3 4 5 6 7 8 h v h/6 h/2 v/2 v/6
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 18 / 30 fig.3 response time the response time is defined as the following figur e and shall be measured by switching the input sign al for ?any level of grey(bright) ? and ?any level of gray(dark )?. any level of gray (bright) any level of gr ay (dark) any level of gray (bright) t (r) 0%, 25%, 50%, 75%, 100% photodetector output time t (f) 0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100% fig.4 viewing angle 90% 90% 90% 90% 1 11 10% 0%0% 0%
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 19 / 30 5. mechanical characteristics the contents provide general mechanical characteris tics for the model t315hw07 v1. in addition the fig ures in the next page are detailed mechanical drawing of the lc d. horizontal 739.6 mm vertical 440.0 mm outline dimension depth 24.1 mm ( front bezel to t-con cover ) horizontal 703.6 mm bezel opening vertical 399.80 mm horizontal 698.40 mm active display area vertical 392.85 mm weight 4600 g (typ.) surface treatment anti-glare, 3h
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 20 / 30 front view
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 21 / 30 back view
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 22 / 30 6. reliability test items test item q?ty condition 1 high temperature storage test 3 60 , 300hrs 2 low temperature storage test 3 -20 , 300hrs 3 high temperature operation test 3 50 , 300hrs 4 low temperature operation test 3 -5 , 300hrs 5 vibration test (non-operation) 3 wave form: random vibration level: 1.0g rms bandwidth: 10-300hz, duration: x, y, z 10min one time each direction 6 shock test (non-operation) 3 shock level: 50g waveform: half since wave, 11ms direction: x, y, z, one time each direction 7 vibration test (with carton) 6 random wave (1.0g rms, 10-200hz) 10mins/ per each x,y,z axes 8 drop test (with carton) 6 height: 381mm 1 corner, 3 edges, 6 surfaces (astmd5276)
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 23 / 30 7. international standard 7.1 safety (1) ul 60950-1, ul 60065; standard for safety of in formation technology equipment including electrical business equipment. (2) iec 60950-1 : 2001, iec 60065:2001 ; standard f or safety of international electrotechnical commission (3) en 60950 : 2001+a11, en 60065:2002+a1:2006; eur opean committee for electrotechnical standardization (cenelec), european standard for sa fety of information technology equipment including electrical business equipment. 7.2 emc (1) ansi c63.4 ?methods of measurement of radio-noi se emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 (2) c.i.s.p.r ?limits and methods of measurement of radio interface characteristics of information technology equipment.? international special commit tee on radio interference. (3) en 55022 ?limits and methods of measurement of radio interface characteristics of information technology equipment.? european committee for elect rotechnical standardization. (cenelec), 1998
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 24 / 30 8. packing 8-1 definition of label: a. panel label: *xxxxxxxxxxxx -xxxx * green mark description (1) for pb free product, auo will add for identification. (2) for rohs compatible products, auo will add rohs for identification. note: the green mark will be present only when the green documents have been ready by auo internal gre en team. (definition of green design follows the auo g reen design checklist.) b. carton label: au optronics t315hw07 v1 97.31t14.100 qty : 6 panel unique id auo internal use xxxxx model no: t315hw07 v.1 xxxxxxx manufactured xx / xx made in x xxxx fab location week year auo internal use auo internal use
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 25 / 30 8-2 packing methods: 6pcs modules 1pcs module/esd bag module cushion set h tape
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 26 / 30 8-3 pallet and shipment information specification item quantity dimension weight (kg) packing remark 1 packing box 6pcs/box 830(l)mm*285(w)mm*537(h)mm 31 2 pallet 1 1150(l)mm*840(w)mm*132(h)mm 13 3 boxes per pallet 8 boxes/pallet 4 panels per pallet 48 pcs/pallet 1150(l)mm*840(w)mm*2460(h)mm 261 5 pallet after packing n/a 1150(l)mm*840(w)mm*2412(h)mm double pallet 522 stretch film label corner angle pet band moisture-proof film corner angle pallet
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 27 / 30 8. precautions please pay attention to the followings when you use this tft lcd module. 9-1 mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to module. and the case on which a module is mounte d should have sufficient strength so that external force is not transmitted directly to the m odule. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit broken by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-h exane is recommended for cleaning the adhesives used to attach front/ rear polarizer. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2 operating precautions (1) the device listed in the product specification sheets was designed and manufactured for tv application (2) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage: v=200mv(over and under shoot voltage) (3) response time depends on the temperature. (in l ower temperature, it becomes longer..) (4) brightness of ccfl depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time (required time tha t brightness is stable after turned on) becomes longer. (5) be careful for condensation at sudden temperatu re change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (6) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (7) module has high frequency circuits. sufficient suppression to the electromagnetic interference sha ll
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 28 / 30 be done by system manufacturers. grounding and shie lding methods may be important to minimize the interface. 9-3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground thro ugh wristband etc. and don?t touch interface pin directly. 9-4 precautions for strong light exposure strong light exposure causes degradation of polariz er and color filter. 9-5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the temperature between 5 and 35 at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that the y be stored in the container in which they were shipp ed. 9-6 handling precautions for protection film (1) the protection film is attached to the bezel wi th a small masking tape. when the protection film i s peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the protection film is peeled off. (3) you can remove the glue easily. when the glue r emains on the bezel or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 29 / 30 appendix 1 edid setting
t315hw07 v1 product specification rev. 0.2 ? copyright auo optronics corp. 2009 all rights res erved. page 30 / 30 appendix 2 t315hw0 7 77 7 v1

▲Up To Search▲

Price & Availability of T315HW07-V1

	To Download T315HW07-V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .